Elsevier

Journal of Biomechanics

Volume 26, Issue 11, November 1993, Pages 1271-1277, 1279-1281
Journal of Biomechanics

Quantitative analysis of bone reactions to relative motions at implant-bone interfaces

https://doi.org/10.1016/0021-9290(93)90351-EGet rights and content

Abstract

Connective soft tissues at the interface between implants and bone, such as in human joint replacements, can endanger the stability of the implant fixation. The potential of an implant to generate interface bone resorption and form soft tissue depends on many variables, including mechanical ones. These mechanical factors can be expressed in terms of relative motions between bone and implant at the interface or deformation of the interfacial material.

The purpose of this investigation was to determine if interface debonding and subsequent relative interface motions can be responsible for interface degradation and soft tissue interposition as seen in experiments and clinical results. A finite element computer program was augmented with a mathematical description of interface debonding, dependent on interface stress criteria, and soft tissue interface interposition, dependent on relative interface motions. Three simplified models of orthopaedic implants were constructed: a cortical bone screw for fracture fixation plates, a femoral resurfacing prosthesis and a straight stem model, cemented in a bone. The predicted computer configurations were compared with clinical observations. The computer results showed how interface disruption and fibrous tissue interposition interrelate and possibly enhance each other, whereby a progressive development of the soft tissue layer can occur.

Around the cortical bone screw, the predicted resorption patterns were relatively large directly under the screw head and showed a pivot point in the opposite cortex. The resurfacing cup model predicted some fibrous tissue formation under the medial and lateral cup rim, whereby the medial layer developed first because of higher initial interface stresses. The straight stem model predicted initial interface failure at the proximal parts. After proximal resorption and fibrous tissue interposition, the medial interface was completely disrupted and developed an interface layer. The distal and mid lateral side maintained within the strength criterion.

Although the applied models were relatively simple, the results showed reasonable qualitative agreement with resorption patterns found in clinical studies concerning bone screws and the resurfacing cup. The hypothesis that interface debonding and subsequent relative (micro)motions could be responsible for bone resorption and fibrous tissue propagation is thereby sustained by the results.

References (39)

  • D.R. Carter

    Mechanical loading history and skeletal biology

    J. Biomechanics

    (1987)
  • K. Draenert

    Histomorphology of the bone-to-cement interface: remodeling of the cortex and revascularization of the medullary canal in animal experiments

  • N.S. Eftekar et al.

    Prosthetic synovitis

  • R. Feith

    Side effects of acrylic cement, implanted into bone

    Acta orthop. scand.

    (1975)
  • S.R. Goldring et al.

    The synoviallike membrane at the bone-cement interface in loose total hip replacements and its proposed role in bone lysis

    J. Bone Jt Surg.

    (1983)
  • T.A. Gruen et al.

    Modes of failure of cemented stem-type femoral components

    Clin. Orthop.

    (1979)
  • W.H. Harris

    The first 32 years of total hip arthroplasty: one surgeon's perspective

    Clin. Orthop. Rel. Res.

    (1992)
  • R.Y. Hori

    Investigation of the bone-prosthesis interface following total joint replacement

  • R.Y. Hori et al.

    Mechanical properties of the fibrous tissue found at the bone-cement interface following total joint replacement

    J. Biomater. Res.

    (1982)
  • Cited by (58)

    • Laser processing of Ti composite coatings reinforced with hydroxyapatite and bioglass

      2018, Additive Manufacturing
      Citation Excerpt :

      Poor wear resistance is another important concern of Ti and its alloys although not required for all implants. However, some areas of the implants, such as interface between hip stem neck and taper bore of the femoral head, experience considerable amount of micro-motions, where increase in the wear resistance of neck can significantly decrease the wear debris generation and improve in vivo life of the implants [8,9]. Generation of metal debris and metal ion release due to micro-motions could lead to implant loosening via osteolysis and metal sensitivity [10–13].

    • Finite element analysis of stresses generated in cortical bone during implantation of a novel Limb Prosthesis Osseointegrated Fixation System

      2017, Biocybernetics and Biomedical Engineering
      Citation Excerpt :

      The most commonly used involve an application of an interference fit between the cylindrical implant (with appropriate anchoring/anti-rotation elements and surface's roughness) and bone, e.g. the ITAP [15]. After around 6 months of osseointegration, a stable implant-bone connection is obtained [5,6,11,20]. Due to the fact that implants for direct skeletal attachment of limb prosthesis are a constantly developing and innovative method, numerous studies are carried out.

    • Non-linear 3D finite element analysis of full-arch implant-supported fixed dentures

      2014, Materials Science and Engineering C
      Citation Excerpt :

      The bone-implant interface represents a great influence on stress in peri-implant bone [44]. It has been suggested that stress in the peri-implant bone and the implant apex is higher for free contact (contact elements) at the bone-implant interface in comparison with bond contact (100% union) [45]. The implants submitted to immediate loading presented a frictional component at the bone interface, and this contact transferred pressure, tangential and frictional forces [39].

    • Microstructure, mechanical and wear properties of laser surface melted Ti6Al4V alloy

      2014, Journal of the Mechanical Behavior of Biomedical Materials
      Citation Excerpt :

      For example, the hip stem in the total hip prosthesis do not undergo any major articulation but significant amount of micro-motions can occur at two interfaces e.g., (i) femoral neck (Ti6Al4V alloy) and femoral head (CoCrMo alloy or Al2O3 or Zirconia toughened Al2O3) and (ii) hip stem and femur bone. These micro-motions can generate high wear debris, which can limit long-term stability of load-bearing implants (Fukunishi, 1995; Weinans et al., 1993). The severity of this problem may be magnified several times in younger and more active patients.

    • Comparison of different designs of implant-retained overdentures and fixed full-arch implant-supported prosthesis on stress distribution in edentulous mandible - A computed tomography-based three-dimensional finite element analysis

      2013, Journal of Biomechanics
      Citation Excerpt :

      The condition of the bone–implant interface has a burly influence on the stress intensities over the peri-implant area (O’Mahony et al., 2001). The stress at the periimplant bone and implant apex are greater for a free contact when compared to a fixed bond (Weinans et al., 1993). Before osseointegration, the implant–bone interface presents a frictional component which allows minor displacement.

    • Wear performance of laser processed tantalum coatings

      2011, Materials Science and Engineering C
      Citation Excerpt :

      Although, HA coatings perform equally well in terms of biological fixation, the low fracture toughness, wear resistance and rough surface morphology of these coatings can generate high wear debris as a result of micro motions at the bone-implant interface during early stages of surgery. These particulate wear debris have been recognized as one of the major challenges for long-term viability of load bearing implants [15,16]. The above problem can be alleviated if HA coatings are replaced with bioactive Ta coatings, as the metallic Ta coatings have high fracture toughness and can be polished to achieve a smooth surface.

    View all citing articles on Scopus

    Partly presented at the 34th Annual Meeting of the Orthopaedic Research Society, January 1988, Atlanta, Georgia.

    View full text